Showing results: 61 - 75 of 293 items found.
-
FAD-100 -
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Long Time Record of Measurement by Input Power Supply・Detection of Both AC Current and DC Current At Once・Detection of Small DC current Inside Large AC Current・Freely Bending with Flexible Clamp Sensor of Inside Diameter 200mm・Useful for difficult Access Locations with Wide Ranges up to AC/DC 1000A
-
CP-02B -
KILTER ELECTRONIC CO.,LTD
Can connect to oscilloscope Test range :10ABandwidth:5Hz~10MHz(-3db)Low battery indication Jaw size: 5mm(Max)Auto Zero at power onRelative Zero correctionWeight: Approx 200gDimensions: 215mm(L)× 58mm(W)× 16mm(H)
-
CP-05 -
KILTER ELECTRONIC CO.,LTD
Connected with Oscilloscope and DMMAC/DC current MeasurementAmorphous Alloy CoreTest range:4A,11us,40A,6us,200A,6us100KHz Noise:20mALow battery indicationSmall size Light weightJaw size:23mm(Max)
-
Extech PQ3210 -
Extech Instruments Corporation
The Extech PQ3210 is a set of three flexible 1200 Amp flex clamps for the Extech PQ3350 3-Phase Power and Harmonics Analyzer. These probes are 304 mm (12 in) long for wrapping around busbars.
-
Extech PQ3220 -
Extech Instruments Corporation
The Extech PQ3220 is a set of 3000 Amp flex clamps (set of 3) for the PQ3350 analyzer. Probes are 61 cm (24 in) for wrapping around bus bars.
-
HA1000 -
Summit Technology, Inc.
The HA1000 is our most accurate current probe. The HA1000 clamp-on current probe measures from 1 to 1000 amps AC.
-
CP031A -
Teledyne LeCroy
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
CP030A -
Teledyne LeCroy
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
TBCP1-200 -
TekBox Singapore Pte. Ltd.
The TBCP1-200 is a fixed aperture RF current monitoring probe.The probe has a 3dB bandwidth of approximately 200 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 40 kHz to 200 MHz.
-
HA5 -
Summit Technology, Inc.
Our HA5 Current Probe covers the measurement range from 20 milliamps to 5 amps, making it the best choice for measuring very small loads and the outputs of CT (Current Transformer) step-down circuits.
-
N2893A -
Keysight Technologies
The Keysight N2893A is a 100 MHz bandwidth, active current probe for InfiniiVision and Infiniium oscilloscopes. The probe features flat bandwidth (DC-100MHz), low noise(<2.5 mA rms) and low circuit insertion loss. Auto demagnetization (degauss) and calibration removes any residual magnetism and unwanted DC offset in the probe. The probe is powered directly by the InfiniiVision and Infiniium Autoprobe interface, eliminating the need for an additional power supply.
-
N7026A -
Keysight Technologies
The Keysight N7026A is a 150 MHz bandwidth, active current probe for InfiniiVision and Infiniium oscilloscopes. The probe features wide and flat bandwidth (DC-150 MHz), lower noise (<250 µArms), and wide input range (up to continuous 30 Arms or non-continuous 40 Apeak). This enables you to measure down to 1 mA/div, giving you a much more accurate view of your low-level signals.
-
HA100 -
Summit Technology, Inc.
The HA100 is a compact clamp-on current probe for smaller loads where compact size is important. Its measurement range is from 0.1 to 100 amps AC and is very small which is ideal for locking inside a crowded electrical panel during monitoring.
-
DRP 503/18 -
GMC-I-PROSyS
The new DRP 503/18 is a 3 Phase Flexible AC current Probe utilising the Rogowski principle, with 3 channel integrator housed in DIN Rail Mounted Enclosure. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas and with large conductors.
-
DRM 504/18 -
GMC-I-PROSyS
The new DRP 504/18 is a 4 Phase Flexible AC current Probe utilising the Rogowski principle, with 4 channel integrator housed in DIN Rail Mounted Enclosure. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas and with large conductors.